Not clad

This code covers rectangular aluminum plates, sheets, and strip—not clad—with a thickness exceeding 0.2mm, specifically detailing various alloy types and thicknesses. Use this code when importing these aluminum products to determine the applicable 3% general duty or free trade agreement (FTA) rates, as outlined in Chapter 76.

Detailed information for HTS Code 7606.12.30

AI Summary

This duty applies to aluminum and articles thereof within Chapter 76, specifically to plates, sheets, and strip of aluminum alloys that are not clad, exceeding 0.2mm in thickness. The code 7606.12.30 covers rectangular forms of this material, and further breakdowns specify thickness (over or under 6.3mm) and alloy type—like high-strength heat-treatable, heat-treatable industrial, or aluminum can stock—to determine the appropriate statistical suffix. Choose the suffix based on both the material’s thickness and its intended use or alloy composition, referencing statistical notes 6 and 7 for alloy definitions.

Chapter	Chapter 76 - Aluminum and articles thereof
Section	Section XV - Base Metals and Articles of Base Metal

Duty snapshot

Quick reference for the duty outcomes tied to this HTS line.

General Duty

Standard trade partners (NTR)

Special Duty

Free (A*,AU,BH,CL,CO,D,E,IL,JO,KR,MA,OM,P,PA,PE,S,SG)

Eligible FTA or preference programs

The general duty rate for HTS code 7606.12.30 and its subdivisions is 3%, applicable to standard trade partners. Several countries (A*, AU, BH, CL, CO, D, E, IL, JO, KR, MA, OM, P, PA, PE, S, SG) qualify for a special duty rate of Free under eligible FTA or preference programs. Reporting units are kilograms. This means imports from the listed countries under qualifying programs will be duty-free, while imports from other countries will be subject to the 3% general duty. The specific subdivisions (7606.12.30.15, 7606.12.30.25, etc.) all follow the same duty structure as the main code, inheriting the general and special rates.

Rate of Duty (Column 2): 13.50%

Need help importing?
_

Submit your details, and our team will confirm the correct classification and answer your questions.

Code subdivisions

7606.12.30.15

Aluminum plates, sheets and strip, of a thickness exceeding 0.2 mm: > Rectangular (including square): > Of aluminum alloys: > Not clad > With a thickness of more than 6.3 mm: > High-strength heat-treatable alloys of a kind described in statistical note 6 to this chapter

7606.12.30.25

Aluminum plates, sheets and strip, of a thickness exceeding 0.2 mm: > Rectangular (including square): > Of aluminum alloys: > Not clad > With a thickness of more than 6.3 mm: > Heat-treatable industrial alloys of a kind described in statistical note 7 to this chapter

7606.12.30.35

Aluminum plates, sheets and strip, of a thickness exceeding 0.2 mm: > Rectangular (including square): > Of aluminum alloys: > Not clad > With a thickness of more than 6.3 mm: > Other

Parent subheading for dairy herd replacements

7606.12.30.45

Aluminum plates, sheets and strip, of a thickness exceeding 0.2 mm: > Rectangular (including square): > Of aluminum alloys: > Not clad > With a thickness of 6.3 mm or less: > Aluminum can stock: > Body stock

7606.12.30.55

7606.12.30.91

Aluminum plates, sheets and strip, of a thickness exceeding 0.2 mm: > Rectangular (including square): > Of aluminum alloys: > Not clad > With a thickness of 6.3 mm or less: > Other: > Heat-treatable industrial alloys of a kind described in statistical note 7 to this chapter

7606.12.30.96

Aluminum plates, sheets and strip, of a thickness exceeding 0.2 mm: > Rectangular (including square): > Of aluminum alloys: > Not clad > With a thickness of 6.3 mm or less: > Other: > Other

View HTS reference

Chapter & section notes

Chapter notes

Harmonized Tariff Schedule of the United States Revision 29 (2025) Annotated for Statistical Reporting Purposes CHAPTER 76 ALUMINUM AND ARTICLES THEREOF XV 76-1 Subheading Notes 1. In this chapter the following expressions have the meanings hereby assigned to them: (a) Aluminum, not alloyed Metal containing by weight at least 99 percent of aluminum, provided that the content by weight of any other element does not exceed the limit specified in the following table: TABLE - Other elements Element Limiting content percent by weight Fe + Si (iron plus silicon) 1 Other elements (1), each 0.1 (2) (1) Other elements are, for example, Cr, Cu, Mg, Mn, Ni, Zn. (2) Copper is permitted in a proportion greater than 0.1 percent but not more than 0.2 percent, provided that neither the chromium nor manganese content exceeds 0.05 percent. (b) Aluminum alloys Metallic substances in which aluminum predominates by weight over each of the other elements, provided that: (i) The content by weight of at least one of the other elements or of iron plus silicon taken together is greater than the limit specified in the foregoing table; or (ii) The total content by weight of such other elements exceeds 1 percent. 2. Notwithstanding the provisions of note 9(c) to section XV, for the purposes of subheading 7616.91 the term "wire" applies only to products, whether or not in coils, of any cross-sectional shape, of which no cross-sectional dimension exceeds 6 mm. Additional U.S. Note 1. For the purposes of heading 7608, the rate of duty "Free (C)" appearing in the "Special" subcolumn applies only to tubes and pipes with attached fittings, suitable for conducting gases or liquids. Statistical Notes l. For the purposes of this chapter, the term "aluminum vanadium master alloy" refers to aluminum alloys which contain by weight 20 percent or more of vanadium. 2. For the purposes of this chapter, the term "aluminum can stock" refers to sheets and strip in coils, of alloys of aluminum in which either manganese or magnesium is the predominant alloying element, not painted, over 0.175 mm but not over 0.432 mm in thickness, and over 254 mm in width, comprising "body stock and "lid stock" as specified below: (a) The term "body stock" refers to aluminum can stock having manganese as the predominant alloying element and having a minimum tensile strength of 262 MPa; and (b) The term "lid stock" refers to aluminum can stock having magnesium as the predominant alloying element and having a minimum tensile strength of 345 MPa. 3. For the purposes of statistical reporting number 7601.20.9080, "sheet ingot" (slabs) refers to aluminum alloys with a rectangular cross-section suitable to be manufactured into other products. Harmonized Tariff Schedule of the United States Revision 29 (2025) Annotated for Statistical Reporting Purposes XV 76-2 Statistical Notes (con.) 4. For the purposes of statistical reporting number 7601.20.9085, "foundry ingot" refers to large castings of aluminum alloys of various shapes other than sheets or slabs to be melted for further processing. 5. For statistical reporting purposes under subheading 7602.00.00, the term “recyclable aluminum” refers to materials that are obsolete, previously used, off-specification, surplus, or incidentally produced and are collected and sorted for processing into a specification-grade commodity. Recyclable materials may also be considered as scrap but do not include solid waste or residue. 6. For the purposes of statistical reporting numbers 7604.29.3030, 7604.29.5020 and 7606.12.3015, “high-strength heat-treatable alloys” refers to aluminum containing by weight 7.0 percent or less of copper or 10.0 percent or less of zinc, and/or are designated as series 2xxx or 7xxx (except 7072) in the Aluminum Association’s specifications of registered alloys. 7. For the purposes of statistical reporting numbers 7604.21.0010, 7604.29.1010, 7604.29.3060, 7604.29.5050, 7606.12.3025 and 7606.12.3091, “heat-treatable industrial alloys” refers to aluminum containing by weight 3.0 percent or less of magnesium and 3.0 percent or less of silicon, and/or are designated as series 6xxx in the Aluminum Association’s specifications of registered alloys. Harmonized Tariff Schedule of the United States Revision 29 (2025) Annotated for Statistical Reporting Purposes XV 76-3

Section notes

SECTION XV BASE METALS AND ARTICLES OF BASE METAL XV-1 Notes 1. This section does not cover: (a) Prepared paints, inks or other products with a basis of metallic flakes or powder (headings 3207 to 3210, 3212, 3213 or 3215); (b) Ferrocerium or other pyrophoric alloys (heading 3606); (c) Headgear or parts thereof of heading 6506 or 6507; (d) Umbrella frames or other articles of heading 6603; (e) Goods of

Latest update

Last updated

November 15, 2025

Revised every January & July

Let's get your shipment cleared

Submit your details and our team will help with classification and compliance.